Stretch wrap gauge is a thickness unit: 100 gauge equals 1 mil, or one thousandth of an inch. Because NIST lists 1 mil as 0.0254 mm, each gauge point is 0.254 microns, and 80 gauge film is about 20 microns thick.
Higher gauge means thicker film. It does not, on its own, mean a stronger wrap, because resin, extrusion process and pre-stretch all change how a film holds a load.
US suppliers quote gauge, while most of the world quotes microns. Buyers who source internationally need both numbers on the same specification.
Stretch Wrap Gauge Chart: Gauge, Mil and Micron
| Gauge | Mil | Microns | Common use |
|---|---|---|---|
| 47 | 0.47 | 11.9 | Pre-stretched hand film |
| 60 | 0.60 | 15.2 | Light, uniform cartons |
| 70 | 0.70 | 17.8 | Light to medium loads |
| 80 | 0.80 | 20.3 | General-purpose pallets |
| 90 | 0.90 | 22.9 | Medium to heavy loads |
| 100 | 1.00 | 25.4 | Heavy loads |
| 120 | 1.20 | 30.5 | Heavy or sharp loads |
| 150 | 1.50 | 38.1 | Very heavy, irregular loads |
To convert any value yourself, multiply gauge by 0.254 to get microns, or divide microns by 0.254 to get gauge. The “common use” column is a starting point for trials, not a rule.
True Gauge vs Equivalent Gauge
Some hand films are sold as “equivalent” or “performance” gauge. The label describes how the film is claimed to perform against a thicker film, not how thick it is.
That can be a fair product, especially for pre-stretched film. It becomes a problem when two quotes are compared as if the gauge numbers measured the same thing.
Ask every supplier for the measured thickness in microns. ASTM D6988 sets out good practice for measuring plastic film specimens, and it notes that it addresses the same subject as ISO 4593.
Write both numbers on the purchase order, for example “80 gauge (20 microns), measured thickness”. A supplier who sells equivalent-gauge film can then quote it as an alternative instead of a substitute.
Check a Roll by Weight
A scale gives a quick cross-check. Net film weight is width × length × thickness × density.
Most PE stretch film is linear low-density polyethylene (LLDPE), and Plastics Europe lists stretch film among LLDPE’s main uses. The same source gives low-density PE a density range of 0.910–0.940 g/cm³, so 0.92 g/cm³ is a fair working value for PE film:
- An 18 in × 1,500 ft roll of true 80 gauge film holds about 3.9 kg (8.6 lb) of film, core excluded.
- A 50 cm × 300 m roll at 20 microns holds about 2.8 kg of film, core excluded.
If a roll labeled 80 gauge weighs well below the calculated figure after you subtract the core, it is thinner or shorter than the label suggests. That does not make it unusable, but it changes the price per kilogram you are really paying. PVC film is much denser, so this check applies to PE film only.

How to Choose the Right Stretch Wrap Thickness
Pick a starting gauge from the load, then adjust it with a trial. These factors move the choice up or down:
- Load weight: heavier pallets need more holding force across the wrap.
- Load shape: uniform cartons spread force evenly, while corners and protrusions concentrate it and puncture thin film.
- Transport: mixed-freight truck routes and ocean containers shake loads more than a short run between two sites.
- Wrapping method: machines with powered pre-stretch can use thinner film than hand wrapping for the same hold.
- Storage: outdoor storage calls for UV-stabilized film, regardless of gauge.
| Load profile | Starting point |
|---|---|
| Light, uniform cartons | 60–70 gauge |
| Mixed cartons, truck freight | 80 gauge |
| Heavy, stable loads | 90–100 gauge |
| Sharp edges, irregular shapes | 100–150 gauge |
Edge boards often solve a puncture problem more cheaply than moving every pallet to a heavier film. Try them before you upgrade the gauge for the whole site.
If your loads are small retail bundles rather than pallets, check when shrink wrap fits better before choosing any stretch gauge.
Hand Wrap vs Machine Wrap Gauge
Hand rolls are narrower and lighter, so one person can carry and pull them around a pallet. Machine rolls are wider and much heavier, and they are built to run through a powered carriage.
Stretching makes film thinner. On a machine with powered pre-stretch, the film is elongated before it reaches the load, so the film on the pallet is much thinner than the gauge printed on the roll.
That is why machine users can often run a lower gauge than hand wrappers for the same load. Pre-stretched hand film applies the same idea in the factory, which is why it is sold at low gauges and is easier to pull.
Whichever method you use, keep the setting fixed during a trial. A change in pre-stretch percentage changes the effective thickness more than a small change in roll gauge.
Signs You Picked the Wrong Gauge
- Tears at corners while wrapping: the film is too thin for the edges, or the load needs edge boards.
- Breaks on the machine: the film cannot take the pre-stretch setting, or the gauge is lower than labeled.
- Loads lean after transit: holding force is too low; add wraps, raise the gauge or choose a film with better stress retention.
- Many more revolutions than expected: the film may be too light, which can cost more than a heavier roll.
- Every pallet looks over-wrapped: the gauge is probably higher than the load needs.
Gauge Is Not the Only Spec
Two films of the same gauge can hold a pallet very differently. Elastic recovery and stress retention, measured under ASTM D5459, describe how tightly the film keeps hugging the load after it is applied.
Wrap pattern matters as much as film. Record the number of revolutions, the overlap between bands, and how many wraps go around the base to lock the load to the pallet.
Cost should be counted per pallet. Weigh a roll before and after wrapping a set number of pallets, then multiply the film used by the price per kilogram.
Running that trial with a supplier is easier when both sides agree on what to measure; these notes on warehouse film trials with a supplier cover the process.

How to Write Gauge on a Stretch Wrap Quote
A gauge quote is only comparable when every supplier prices the same thickness. Put these lines on the request:
| Line | Example entry |
|---|---|
| Thickness | 80 gauge (20 µm), measured |
| Alternatives | Equivalent gauge quoted separately |
| Width and length | 18 in × 1,500 ft |
| Net film weight | Per roll, core excluded |
| Core | Inside diameter |
| Grade | Hand or machine |
| Color | Clear or black |
The net weight line lets you run the roll-weight check above when the first delivery arrives. If the stated width, length and net weight agree with the calculation, the roll is very likely the gauge you paid for.
When you match a gauge to a supplier’s micron range, convert it first; for example, a quote listed at 23 µm is about 90 gauge. For other film types, browse the full plastic film catalog.
Note your pallet weights, load shapes, transport routes and wrapping method. Then open the heavy-duty logistics wrapping film page and send your target thickness, width and roll size for a quote and samples.
Stretch Wrap Gauge FAQ
What Is Thicker, 60 Gauge or 80 Gauge Stretch Wrap?
80 gauge is thicker: about 20.3 microns against 15.2 microns for 60 gauge. It is the more common general-purpose choice.
How Thick Is 120 Gauge Stretch Wrap?
120 gauge film is 1.2 mil, or about 30.5 microns. It is used for heavy or sharp-edged loads.
What Is Gauge in Stretch Film?
Gauge is the US thickness unit for film, where 100 gauge equals 1 mil. One gauge point equals 0.254 microns.
How Strong Is 80 Gauge Stretch Wrap?
Strength depends on resin, extrusion process and wrap pattern, not on gauge alone. 80 gauge is widely sold as general-purpose hand film, but a trial on your own pallets is the reliable test.


